sorabji.com > foundcrap > found floppies > specdisk


������������������������ SECTION 07464

 

������������������������ VINYL SIDING

This section is based on vinyl siding and soffit systems produced by:

��� Wolverine Technologies

��� 17199 Laurel Park Drive North

��� Livonia, Michigan� 48152

��� Telephone:� 800-521-9020

 

Products include many types and styles of solid vinyl siding and both ventilating and solid soffit systems.� Wolverine Technologies solid vinyl siding has been tested by many independent testing laboratories and approved for use under numerous building codes.

 

PART 1� GENERAL

 

1.1 SECTION INCLUDES

Delete items below not required for project.

��� A.� Solid vinyl siding and accessories.

 

��� B.� Solid vinyl soffit and accessories.

 

��� C.� Vented vinyl soffit and accessories.

 

1.2 RELATED SECTIONS

Delete any sections below not relevant to this project; add others as required.

��� A.� Section 06112 - Framing and Sheathing.

 

��� B.� Section 07191 - Vapor Retarders.

 

��� C.� Section 07900 - Joint Sealers.

 

1.3 REFERENCES

 

��� A.� ASTM D 1435 -- Standard Practice for Outdoor Weathering of Plastics.

 

��� B.� ASTM D 3679 -- Standard Specification for Rigid Poly (Vinyl Chloride) (PVC) Siding.

 

1.4 PERFORMANCE REQUIREMENTS

 

��� A.� Provide vinyl siding and accessories that comply with requirements of ASTM D 3679, Class 2.

������� 1.� Cell classification:� 1334.

������� 2.� Tensile strength:� 7,344 psi.

������� 3.� Modulus of elasticity:� 455,750 psi average.

������� 4.� Izod impact, standard 1/8 inch bar:� 1.5 ft.lbs/in average.

������� 5.� Deflection temperature:� 168 degrees F.

������� 6.� Flash ignition temperature:� 752 degrees F.

������� 7.� Self ignition temperature:� 842 degrees F.

������� 8.� Maximum smoke density:� 86 percent.

������� 9.� Smoke density rating:� 52.4 percent average.

������� 10. Flammability, horizontal:

����������� a.� Burn distance:� Less than 10 mm.

����������� b.� Burn time:� Less than� 5 seconds.

������� 11. Flammability, vertical:� Non-burning.

������� 12. Wind load resistance:� 58.2 ft-lbs/sq. ft.

 

1.5 SUBMITTALS

 

��� A.� Submit under provisions of Section 01300.

 

��� B.� Product Data:� Manufacturer's standard information and installation instructions on vinyl siding and accessories.

 

��� C.� Selection Samples:� Submit full range of color chips for Architect's selection.

 

��� D.� Verification Samples:� Submit three samples of siding products in color specified, not less than 12 inches in length.

Delete article below if Symmetry siding is not required for project.

1.6 QUALITY ASSURANCE

 

��� A.� Symmetry Siding Installer:� Trained installer certified and approved by siding manufacturer.

 

1.7 DELIVERY, STORAGE, AND HANDLING

 

��� A.� Deliver products to project site in original packaging.

 

��� B.� Store siding products on flat surface under cover, stacked no more than 12 boxes high.� Do not store in any location where temperatures may exceed 130 degrees F.

 

1.8 WARRANTY

 

��� A.� Provide manufacturer's standard limited lifetime, non-prorated warranty, transferable to new owner.

 

 

PART 2� PRODUCTS

 

2.1 MANUFACTURER

 

��� A.� Provide vinyl siding products manufactured by Wolverine Technologies, 17199 Laurel Park Drive North;� Livonia, Michigan� 48152.� Telephone:� 800-521-9020.

 

��� B.� Substitutions will not be acceptable.

 

2.2 PRODUCTS

 

��� A.� Material Properties:� Provide polyvinyl chloride products with properties that meet or exceed the following:

������� 1.� Shrinkage:� 3 percent.

������� 2.� Coefficient of linear expansion:� 0.000031 in/in./degree F.

������� 3.� Gardner impact:� 1.74 in./lb ft/mil.

������� 4.� Surface distortion at 120 degrees F:� None.

������� 5.� Gloss (75 degree T Gloss Meter):� Uniform.

������� 6.� Weathering per ASTM D 1435:� Free of any visual surface defects, such as peeling, chipping, cracking, flaking or crazing due to manufacturing conditions.

������� 7.� Chalking:� Number 6 Rating caused by manufacturing defects within 5 years in vertical exposure.

������� 8.� Color:� Uniform on surface and throughout the panels.

 

2.3 VINYL SIDING

Retain only the siding type or types required for your project from those listed below;� delete the others.� Determine desired approach to color and delete alternative text under each siding type.

��� A.� Symmetry:

������� 1.� Design:� Double 4.5 inch clapboard (D45FFP); brushed finish.

������� 2.� Width:� 9 inches +/-0.062 in.

������� 3.� Length:� 40 feet +/- 0.25 in.

������� 4.� Average Thickness:� 0.044 in.

������� 5.� Exposure:� 4.5 in.

������� 6.� Maximum Warp (per 2 panels):� 0.125 in.

������� 7.� Color:� As selected by Architect from manufacturer's standards.

������� 8.� Color:� _______________.

 

��� B.� Restoration Portfolio HP:

������� 1.� Design:� Double 4.5 inch clapboard (D45HP); smooth finish.

������� 2.� Width:� 9 inches +/-0.062 in.

������� 3.� Length:� 12 feet, 1 inch +/- 0.25 in.

������� 4.� Average Thickness:� 0.055 in.

������� 5.� Exposure:� 4.5 in., staggered double nail hem.

������� 6.� Maximum Warp (per 2 panels):� 0.250 in.

������� 7.� Color:� As selected by Architect from manufacturer's standards.

������� 8.� Color:� _______________.

 

��� C.� Restoration Chapel Hill:

������� 1.� Design:� 6 inch with 1/2 inch bead (RSCH), smooth finish.

������� 2.� Width:� 6.5 inches +/-0.062 in.

������� 3.� Length:� 12 feet, 4 inches +/- 0.25 in.

������� 4.� Average Thickness:� 0.044 in.

������� 5.� Exposure:� 6.5 in., staggered double nail hem.

������� 6.� Maximum Warp (per 2 panels):� 0.250 in.

������� 7.� Color:� As selected by Architect from manufacturer's standards.

������� 8.� Color:� _______________.

 

��� D.� Restoration Monterey IV:

������� 1.� Design:� Double 4 inch rounded clapboard (RS4R); smooth finish.

������� 2.� Width:� 8 inches +/-0.062 in.

������� 3.� Length:� 12 feet, 1 inch +/- 0.25 in.

������� 4.� Average Thickness:� 0.044 in.

������� 5.� Exposure:� 4 in., staggered double nail hem.

������� 6.� Maximum Warp (per 2 panels):� 0.250 in.

������� 7.� Color:� As selected by Architect from manufacturer's standards.

������� 8.� Color:� _______________.

 

��� E.� Restoration Stockbridge:

������� 1.� Design:� Double 4.5 Dutchlap (RS45DL); smooth finish.

������� 2.� Width:� 9 inches +/-0.062 in.

������� 3.� Length:� 12 feet, 1 inch +/- 0.25 in.

������� 4.� Average Thickness:� 0.044 in.

������� 5.� Exposure:� 4.5 in., staggered double nail hem.

������� 6.� Maximum Warp (per 2 panels):� 0.250 in.

������� 7.� Color:� As selected by Architect from manufacturer's standards.

������� 8.� Color: �_______________.

 

��� F.� Vinal Side Classic:

������� 1.� Design:� Triple 3 inch clapboard (T3VS); smooth finish.

������� 2.� Width:� 9 inches +/-0.062 in.

������� 3.� Length:� 12 feet, 1 inch +/- 0.25 in.

������� 4.� Average Thickness:� 0.044 in.

������� 5.� Exposure:� 3 in., single nailing hem.

������� 6.� Maximum Warp (per 2 panels):� 0.250 in.

������� 7.� Color:� As selected by Architect from manufacturer's standards.

������� 8.� Color:� _______________.

 

��� G.� Vinal Side Classic:

������� 1.� Design:� Single 8 inch clapboard (S8CL); smooth finish.

������� 2.� Width:� 8 inches +/-0.062 in.

������� 3.� Length:� 12 feet, 6 inches +/- 0.25 in.

������� 4.� Average Thickness:� 0.044 in.

������� 5.� Exposure:� 8 in., single nailing hem.

������� 6.� Maximum Warp (per 2 panels):� 0.250 in.

������� 7.� Color:� As selected by Architect from manufacturer's standards.

������� 8.� Color:� _______________.

 

��� H.� Vinal Side Classic:

������� 1.� Design:� Double 4.5 inch clapboard (D45VS); smooth finish.

������� 2.� Width:� 9 inches +/-0.062 in.

������� 3.� Length:� 12 feet, 1 inch +/- 0.25 in.

������� 4.� Average Thickness:� 0.044 in.

������� 5.� Exposure:� 4.5 in., single nailing hem.

������� 6.� Maximum Warp (per 2 panels):� 0.250 in.

������� 7.� Color:� As selected by Architect from manufacturer's standards.

������� 8.� Color:� _______________.

 

��� I.� Benchmark Reinforced Vinyl Siding:

������� 1.� Design:� Double 4 inch clapboard (BRSD4); woodgrain finish.

������� 2.� Width:� 8 inches +/-0.062 in.

������� 3.� Length:� 12 feet, 6 inches +/- 0.25 in.

������� 4.� Average Thickness:� 0.042 in.

������� 5.� Exposure:� 4 in., single nailing hem with stabilizer reinforcement.

������� 6.� Maximum Warp (per 2 panels):� 0.250 in.

������� 7.� Color:� As selected by Architect from manufacturer's standards.

������� 8.� Color:� _______________.

 

��� J.� Benchmark Reinforced Vinyl Siding:

������� 1.� Design:� Double 4.5 inch clapboard (BRSDL45); woodgrain finish.

������� 2.� Width:� 9 inches +/-0.062 in.

������� 3.� Length:� 12 feet, 1 inch +/- 0.25 in.

������� 4.� Average Thickness:� 0.042 in.

������� 5.� Exposure:� 4.5 in., single nailing hem with stabilizer reinforcement.

������� 6.� Maximum Warp (per 2 panels):� 0.250 in.

������� 7.� Color:� As selected by Architect from manufacturer's standards.

������� 8.� Color: �_______________.

 

��� K.� Benchmark Reinforced Vinyl Siding:

������� 1.� Design:� Double 5 inch clapboard (BRSD5); woodgrain finish.

������� 2.� Width:� 10 inches +/-0.062 in.

������� 3.� Length:� 12 feet +/- 0.25 in.

������� 4.� Average Thickness:� 0.042 in.

������� 5.� Exposure:� 5 in., single nailing hem with stabilizer reinforcement.

������� 6.� Maximum Warp (per 2 panels):� 0.250 in.

������� 7.� Color:� As selected by Architect from manufacturer's standards.

������� 8.� Color:� _______________.

 

��� L.� American Legend:

������� 1.� Design:� 4 inch clapboard (ALD4); woodgrain finish.

������� 2.� Width:� 8 inches +/-0.062 in.

������� 3.� Length:� 12 feet, 6 inches +/- 0.25 in.

������� 4.� Average Thickness:� 0.042 in.

������� 5.� Exposure:� 4 in., single nailing hem.

������� 6.� Maximum Warp (per 2 panels):� 0.250 in.

������� 7.� Color:� As selected by Architect from manufacturer's standards.

������� 8.� Color:� _______________.

 

��� M.� American Legend:

������� 1.� Design:� 5 inch clapboard (ALD5); woodgrain finish.

������� 2.� Width:� 10 inches +/-0.062 in.

������� 3.� Length:� 12 feet +/- 0.25 in.

������� 4.� Average Thickness:� 0.042 in.

������� 5.� Exposure:� 5 in., single nailing hem.

������� 6.� Maximum Warp (per 2 panels):� 0.250 in.

������� 7.� Color:� As selected by Architect from manufacturer's standards.

������� 8.� Color:� _______________.

 

��� N.� American Legend:

������� 1.� Design:� 4.5 inch Dutchlap (AL45DL); woodgrain finish.

������� 2.� Width:� 9 inches +/-0.062 in.

������� 3.� Length:� 12 feet, 1 inch +/- 0.25 in.

������� 4.� Average Thickness:� 0.042 in.

������� 5.� Exposure:� 4.5 in., single nailing hem.

������� 6.� Maximum Warp (per 2 panels):� 0.250 in.

������� 7.� Color:� As selected by Architect from manufacturer's standards.

������� 8.� Color:� _______________.

 

��� O.� Encore:

������� 1.� Design:� Double 4 inch clapboard (ED4); woodgrain finish.

������� 2.� Width:� 8 inches +/-0.062 in.

������� 3.� Length:� 12 feet, 6 inches +/- 0.25 in.

������� 4.� Average Thickness:� 0.040 in.

������� 5.� Exposure:� 4 in., single nailing hem.

������� 6.� Maximum Warp (per 2 panels):� 0.250 in.

������� 7.� Color:� As selected by Architect from manufacturer's standards.

������� 8.� Color:� _______________.

 

��� P.� Encore:

������� 1.� Design:� Double 4.5 inch Dutchlap (EDL45); woodgrain finish.

������� 2.� Width:� 9 inches +/-0.062 in.

������� 3.� Length:� 12 feet, 1 inch +/- 0.25 in.

������� 4.� Average Thickness:� 0.040 in.

������� 5.� Exposure:� 4.5 in., single nailing hem.

������� 6.� Maximum Warp (per 2 panels):� 0.250 in.

������� 7.� Color:� As selected by Architect from manufacturer's standards.

������� 8.� Color:� _______________.

 

��� Q.� Encore:

������� 1.� Design:� Double 5 inch clapboard (ED5); woodgrain finish.

������� 2.� Width:� 10 inches +/-0.062 in.

������� 3.� Length:� 12 feet +/- 0.25 in.

������� 4.� Average Thickness:� 0.040 in.

������� 5.� Exposure:� 5 in., single nailing hem.

������� 6.� Maximum Warp (per 2 panels):� 0.250 in.

������� 7.� Color:� As selected by Architect from manufacturer's standards.

������� 8.� Color:� _______________.

 

��� R.� Encore:

������� 1.� Design:� Triple 3 inch clapboard (ET3); woodgrain finish.

������� 2.� Width:� 9 inches +/-0.062 in.

������� 3.� Length:� 12 feet, 1 inch +/- 0.25 in.

������� 4.� Average Thickness:� 0.040 in.

������� 5.� Exposure:� 3 in., single nailing hem.

������� 6.� Maximum Warp (per 2 panels):� 0.250 in.

������� 7.� Color:� As selected by Architect from manufacturer's standards.

������� 8.� Color:� _______________.

 

��� S.� Weatherstone:

������� 1.� Design:� Double 4 inch clapboard (D4COX); woodgrain finish.

������� 2.� Width:� 8 inches +/-0.062 in.

������� 3.� Length:� 12 feet, 6 inches +/- 0.25 in.

������� 4.� Average Thickness:� 0.040 in.

������� 5.� Exposure:� 4 in., single nailing hem.

������� 6.� Maximum Warp (per 2 panels):� 0.250 in.

������� 7.� Color:� As selected by Architect from manufacturer's standards.

������� 8.� Color:� _______________.

 

��� T.� Weatherstone:

������� 1.� Design:� Double 5 inch clapboard (D5COX); woodgrain finish.

������� 2.� Width:� 10 inches +/-0.062 in.

������� 3.� Length:� 12 feet +/- 0.25 in.

������� 4.� Average Thickness:� 0.040 in.

������� 5.� Exposure:� 5 in., single nailing hem.

������� 6.� Maximum Warp (per 2 panels):� 0.250 in.

������� 7.� Color:� As selected by Architect from manufacturer's standards.

������� 8.� Color:� _______________.

 

��� U.� Weatherstone:

������� 1.� Design:� Double 5 inch Dutchlap (WS5DL); woodgrain finish.

������� 2.� Width:� 10 inches +/-0.062 in.

������� 3.� Length:� 12 feet +/- 0.25 in.

������� 4.� Average Thickness:� 0.040 in.

������� 5.� Exposure:� 5 in., single nailing hem.

������� 6.� Maximum Warp (per 2 panels):� 0.250 in.

������� 7.� Color:� As selected by Architect from manufacturer's standards.

������� 8.� Color:� _______________.

 

2.4 SIDING ACCESSORIES

Retain most of the standard accessories for any siding type, unless you wish to use optional accessories;� for Symmetry Siding, use Designer Corner Posts and J-Channels.

��� A.� Standard Accessories:

������� 1.� Corner post:� Standard width, 10 feet length.

������� 2.� J-Channel:� Standard width, 12 feet, 6 inches length.

������� 3.� Utility trim:� 12 feet, 6 inches length.

������� 4.� Dual undersill trim:� 12 feet, 6 inches length.

������� 5.� Springlock starter:� 2-1/2 inches by 10 feet length.

������� 6.� Color: ________________.

Restoration trim options can be used with any Restoration Siding and with any Vinal Side Classic Siding.

��� B.� Optional Accessories:

������� 1.� Designer Corner Trim:� 5 inch face by 20 feet length.

������� 2.� Designer J-channel:� 3/4 inch pocket height by 2-1/4 inch pocket depth by 12 feet, 6 inches length.

������� 3.� Smarter Starter:� 2-1/2 inch by 10 feet length.

������� 4.� Restoration 5 inch Box Post: 5 inch by 10 feet length.

������� 5.� Restoration 5 inch Box Post: 5 inch by 20 feet length.

������� 6.� Restoration Window/Door Surrounds:� 3-1/2 inch by 12 feet, 6 inches length.

������� 7.� Restoration Window/Door Surrounds:� 3-1/2 inch by 20 feet length.

������� 8.� Restoration Crown Molding:� 2-1/2 inch by 10 feet length.

������� 9.� Color:� ______________.

 

2.5 VINYL SOFFIT

 

��� A.� Restoration Beaded Soffit:

������� 1.� Design:� Triple 2 inch solid (RSTCW6); smooth finish.

������� 2.� Width:� 6 inches +/-0.062 in.

������� 3.� Length:� 12 feet, 6 inches +/- 0.25 in.

������� 4.� Average Thickness:� 0.039 in.

������� 5.� Exposure:� 6 in., single nailing hem.

������� 6.� Maximum Warp (per 2 panels):� 0.250 in.

������� 7.� Color:� As selected by Architect from manufacturer's standards.

������� 8.� Color:� _______________.

 

��� B.� Restoration Invisivent:

������� 1.� Design:� Triple 2 inch vented (RSCW6V); smooth finish.

������� 2.� Width:� 6 inches +/-0.062 in.

������� 3.� Length:� 12 feet, 6 inches +/- 0.25 in.

������� 4.� Average Thickness:� 0.039 in.

������� 5.� Exposure:� 6 in., single nailing hem.

������� 6.� Ventilation:� 1.06 sq. inches per sq. ft.

������� 7.� Maximum Warp (per 2 panels):� 0.250 in.

������� 8.� Color:� As selected by Architect from manufacturer's standards.

������� 9.� Color:� _______________.

 

��� C.� Soffit Accessories:

������� 1.� J-Channel:� 3/8 inch by 12 feet, 6 inch length, for vertical and eave applications.

������� 2.� Soffit Double Channel Lineal:� 3/8 inch by 12 feet, 6 inches length, for eave applications.

������� 3.� Color:� _______________.

 

2.6 FASTENERS AND ACCESSORIES

 

��� A.� Fasteners:� Galvanized nails or other corrosion-resistant fasteners, as recommended by manufacturer for specific application.

 

��� B.� Joint Sealers:� As specified in Section 07900.

 

 

PART 3� EXECUTION

 

3.1 EXAMINATION

 

��� A.� Prior to beginning installation of vinyl siding products, examine substrate conditions.� Verify governing dimensions and acceptability of substrate.� Do not proceed with installation until unsatisfactory conditions have been corrected.

 

3.2 INSTALLATION

 

��� A.� Install vinyl siding products in strict accordance with manufacturer's instructions.

Delete paragraph below if no Symmetry siding is required for project.

��� B.� Install Symmetry siding using pre-manufactured clip system approved by siding manufacturer.

 

��� C.� Attach products securely to substrate for weathertight installation, with all joints true and plumb.��

 

3.3 ADJUSTING AND CLEANING

 

��� A.� Clean any dirt from surface of installed products, using mild soap and water.

 

��� B.� Upon completion of installation, remove from project site excess materials and debris caused by vinyl siding installation.

 

 

����������������������� Back to SPECDISK Table of Contents


sorabji.com > foundcrap > found floppies > specdisk