������������������������ SECTION 08215

 

������������������ STILE AND RAIL WOOD DOORS

This section is based on the IWP Prehung Door System manufactured by International Wood Products, a Division of 3D Industries, Inc., Part of the JELD-WEN Family, at the following address:

���� 7312 Convoy Court

���� San Diego, CA 92111

���� Telephone:� (800) 468-3667 or (619) 496-2121

���� Fax:� (800) 426-8655

 

International Wood Products doors are solid hardwood stile and rail entrance doors with glazed lights, carved panels, sidelights, and transoms, fully factory assembled and finished.� Matching interior panelled doors and french doors are also available.

 

PART 1� GENERAL

 

1.1 SECTION INCLUDES

Delete items below not required for project.

��� A.� Factory-assembled prehung door system, with:

������� 1.� Stile and rail wood entrance doors.

������� 2.� Frames.

������� 3.� Sidelights.

������� 4.� Transoms.

������� 5.� Glazing.

Delete one of the following 2 paragraphs:� Use the first if the door manufacturer is to provide the entrance lockset, the second if not.

������� 6.� All door hardware.

������� 7.� All door hardware except locksets and strikes.

 

��� B.� Matching interior doors, with frames.

 

��� C.� Matching french doors, with frames.

 

1.2 RELATED SECTIONS

Delete any sections below not relevant to this project; add others as required.

��� A.� Section 08710 - Door Hardware, for locksets and strikes.

 

��� B.� Section 08800 - Glazing, for glazing in doors.

 

1.3 REFERENCES

Delete references from the list below that are not actually required by the text of the edited section.

��� A.� 16 CFR 1201 ‑‑ Safety Standard for Architectural Glazing Materials; Consumer Products Safety Commission.

 

1.4 SUBMITTALS

 

��� A.� Submit under provisions of Section 01300.

 

��� B.� Product Data:� Show construction and finish materials.

 

��� C.� Shop Drawings:� Submit fabrication and assembly drawings for each different door assembly.

 

��� D.� Selection Samples:� Finish color samples.

 

��� E.� Glazing Installation Templates:� Provide to installer of glazing.

 

��� F.� Lockset Templates:� Obtain from door hardware provider.

 

1.5 QUALITY ASSURANCE

 

��� A.� Glazing:� Comply with 16 CFR 1201, the federal safety glazing rules.

 

1.6 DELIVERY, STORAGE, AND HANDLING

 

��� A.� Provide substantial packaging sufficient to prevent damage to components and factory finishes.

 

1.7 WARRANTY

 

��� A.� Provide manufacturer's standard warranty.

 

 

PART 2� PRODUCTS

 

2.1 MANUFACTURERS

Delete one of the following 2 paragraphs.� See the manufacturer's literature for designs and species available in each series.�

��� A.� Provide the IWP Prehung Door System manufactured by International Wood Products, a Division of 3D Industries, Inc., part of the JELD-WEN Family; 7312 Convoy Court, San Diego, CA 92111.� Telephone:� (800) 468-3667.� Fax:� (800) 426-8655.

 

��� B.� Provide "Advantage Wood Specialties" Prehung Door System, manufactured by International Wood Products, a Division of 3D Industries, Inc., part of the JELD-WEN Family; 7312 Convoy Court, San Diego, CA 92111.� Telephone: (800) 468‑3667.� Fax:� (800) 426-8655.

 

2.2 DOOR ASSEMBLIES

This section of the specification is designed to allow the specifier specify a single door assembly or create a "schedule" of all the stile and rail doors on the project.� If more than one door type, or combination of features, is required, copy the entire set of options as many times as necessary and edit each copy for the particular door type.� The title "Entrance Doors" in each copy should then be changed to reflect the location or other designation of that door type, to link the specification with the drawings.� After editing this section go on to subsequent articles in Part 2 and delete materials and components not used.

��� A.� Entrance Doors:� Design No. ________.

Delete either swinging in or out.

������� 1.� Swinging in.

������� 2.� Swinging out.

Delete all but one of the following 3 paragraphs.

������� 3.� Single door hinged on right (viewed from exterior).

������� 4.� Single door hinged on left (viewed from exterior).

������� 5.� Pair of doors.

Delete all but one of the following 4 paragraphs.� Other widths are available, both standard and non-standard: enter the actual door width in the blank.

������� 6.� Door width:� 30 inches.

������� 7.� Door width:� 32 inches.

������� 8.� Door width:� 36 inches.

������� 9.� Door width:� __________.

Standard height for entrance doors is 80 inches; other heights are available.

������� 10. Door height:� 80 inches.

������� 11. Door height:� 84 inches.

������� 12. Door height:� 96 inches.

������� 13. Door height:� _________.

Standard thickness for entrance doors is 1-3/4 inch; 2-1/4 inch also available.� For narrower doors and interior doors 1-3/8 inch may be acceptable.

������� 14. Door thickness:� 1-3/4 inches.

������� 15. Door thickness:� ____________.

Delete all but one of the following 4 paragraphs.� Other sizes available.

������� 16. Jamb depth:� 4-9/16 inches.

������� 17. Jamb depth:� 5-1/4 inches.

������� 18. Jamb depth:� 6-1/2 inches.

������� 19. Jamb depth:� 7-1/2 inches.

������� 20. Jamb depth:� ____________.

Delete one of the following 2 paragraphs.

������� 21. Weatherstripped jambs.

������� 22. No weatherstripping.

Delete all but one of the following 3 paragraphs if sidelights are included.� Otherwise, delete all.

������� 23. Sidelight on left, to match (viewed from exterior).

������� 24. Sidelight on right, to match (viewed from exterior).

������� 25. Sidelights on both sides, to match.

Enter the total width in the blank.

������� 26. Total entrance width:� __________

Delete the transom paragraph if not included.

������� 27. Transom, to match; Design No. _________

Enter the total height in the blank.

������� 28. Total entrance height:� ___________

Delete all but one of the following 3 paragraphs.� Other hardwood species available.

������� 29. Species:� Red oak.

������� 30. Species:� Genuine mahogany.

������� 31. Species:� Paint grade maple.

������� 32. Species:� Stain grade Hard maple.

������� 33. Species:� Cherry.

Delete all but one of the following 4 paragraphs.

������� 34. Frame casing:� Streamline, 3/4 inch x 2-1/4 inch.

������� 35. Frame casing:� Colonial, 3/4 inch x 2-1/4 inch.

������� 36. Frame casing:� Colonial, 3/4 inch x 3-1/2 inch.

������� 37. Frame casing:� Fluted, 3/4 inch x 3-1/2 inch.

Delete all but one of the following glazing paragraphs.

������� 38. Glazing:� Leaded; Design No. ________.

Delete either caming material.� Brass and chrome caming must be triple-glazed to keep the finish bright.� Triple-glazing is optional with lead caming.

����������� a.� Cames:� Dark gray lead.

����������� b.� Cames:� Bright brass.

����������� c.� Cames:� Polished zinc.

Triple-glazing required for brass and polished zinc caming, optional for lead caming.� Delete if not required.

����������� d.� Clear sheet glass outer and inner panes, for triple-glazing.

������� 39. Glazing:� Clear 1/4 inch tempered glass.

������� 40. Glazing:� Sealed insulating units, clear.

������� 41. Glazing:� By others.

������� 42. Glazing:� ______________.

Delete either transparent or opaque finish.� Paint grade maple is usually specified for opaque finish because it is less expensive.

������� 43. Finish:� Transparent finish; catalyzed polyurethane "Permalane II Finish System".

����������� a.� Color:� Wheat.

����������� b.� Color:� Chappo.

����������� c.� Color:� Tobacco.

����������� d.� Color:� Cherry.

����������� e.� Color:� Jacobean.

����������� f.� Color:� Whitewash.

������� 44. Finish:� Opaque primer.

������� 45. Finish:� Opaque finish coating, as specified below.

����������� a.� Color as selected by Architect from door manufacturer's standard selection.

����������� b.� Color:� __________.

������� 46. Finish:� Transparent Designer Tints.

����������� a.� Color as selected by Architect from door manufacturer's standard selection.

����������� b.� Color:� __________.

 

2.3 MATERIALS

 

��� A.� Wood Members:� Kiln-dried solid hardwood of species indicated, no veneers.

 

��� B.� Hinges:� Solid brass, ball-bearing full mortise butt hinges; 4-1/2 x 4-1/2 inches; square cornered; 3 per leaf for doors up to 84 inches in height, 4 per leaf for 96 inch height.

 

��� C.� Weatherstripping:� "Q-LON" recessed into kerf in jamb members.

 

��� D.� Flushbolts:� Solid brass, fully recessed in edge of door; provide top and bottom bolts on inactive leaf of double doors.

Delete either adjustable sill with metal threshold or the following solid oak sill.

��� E.� Sills:� Treated hardwood subsill, covered with sloping metal threshold and vertically adjustable oak sill cover.

Delete one of the following 2 paragraphs.

������� 1.� Threshold:� Solid extruded brass.

������� 2.� Threshold:� Extruded aluminum.

Delete one of the following 2 paragraphs.� Also, delete both if brass threshold is used.

������� 3.� Aluminum finish:� Anodized, dark bronze.

������� 4.� Aluminum finish:� Anodized, brass.

Delete solid oak sill if not used.

��� F.� Sills:� Sloped, solid oak.

 

��� G.� Door Sweep:� Neoprene sweep with metal dripcap on exterior, matching threshold.

Delete the following paragraph if locksets are not to be furnished by the door manufacturer.

��� H.� Entrance Lockset:� "Jado"; furnished and installed by door manufacturer.

������� 1.� Style as selected by Architect from door manufacturer's standard selection.

 

2.4 FABRICATION

 

��� A.� Use mortise and tenon construction for doors and frames.� Use Type I Exterior glue for all joints.

 

��� B.� Fabricate vertical posts from one piece.

 

��� C.� At pairs of doors provide T-shaped astragal and flushbolts on inactive leaf.

 

��� D.� Fully machine and assemble prior to finishing.

 

��� E.� Machine sand with super fine No. 220 grit paper followed by hand sanding.� Leave no machine or cross grain sand marks.

 

��� F.� Prepare door for lockset.

 

��� G.� Disassemble into major components and finish each separately.

 

��� H.� Factory-install all glazing.

 

��� I.� Reassemble and make necessary adjustments.� Disassemble and pack for shipment.

 

2.5 FINISHES

 

��� A.� Transparent Finish:� Factory applied catalyzed polyurethane, "Permalane II Finish System."

������� 1.� One coat penetrating wiping stain.

������� 2.� Two coats catalyzed stain sealer with fine sanding between coats.

������� 3.� Hand applied open grain filler.

������� 4.� Two coats of dual component aliphatic polyurethane with ultraviolet absorbers.� Fine sanding between coats.

������� 5.� Oven-cured top coats.

������� 6.� Hand rubbed to smooth satin finish.

 

��� B.� Opaque Finish:� Factory applied PPG "Flexacron."

������� 1.� Prime coating:� Two coats.

������� 2.� Finish coating:� 6-step finish.

 

 

PART 3� EXECUTION

 

3.1 PREPARATION

 

��� A.� Adjust rough opening as required to fit door assembly.

 

3.2 INSTALLATION

 

��� A.� Install door assemblies in accordance with manufacturer's instructions and recommendations.

 

��� B.� Install door assemblies plumb, true and level, with moving components operating smoothly.

 

 

����������������������� Back to SPECDISK Table of Contents

---

sorabji.com > foundcrap > found floppies > specdisk