������������������������ SECTION 08740

 

����������������� ELECTRICAL LOCKING SYSTEMS

This section is based on products manufactured by OSI Security Devices, at the following address:

���� 657 North Pastoria Avenue

���� Sunnyvale, California� 94086

���� Telephone:� 408-720-0909

���� Fax:� 408-720-9034

 

"Omnilock" locksets are self-contained electronic access control systems featuring keypad programming and multi-level user codes.� The series includes both heavy-duty cylindrical and mortise locks with lever or knob trim, or trimless to accept existing trim.� A wall mounted unit is available for connection to electromagnetic or electromechanical locks.

 

Each lockset is self-contained, and requires no outside source of power or control wiring.�

 

PART 1� GENERAL

 

1.1 SECTION INCLUDES

Delete items below not required for project.

��� A.� Cylindrical locksets with programmable access modules.

 

��� B.� Mortise locksets with programmable access modules.

 

��� C.� Wall mounted modules with programmable access for connection to electromagnetic or electromechanical locks (specified elsewhere).

 

1.2 RELATED SECTIONS

Delete any sections below not relevant to this project;� add others as required.

��� A.� Section 08110 - Steel Doors and Frames.

 

��� B.� Section 08210 - Wood Doors.

 

��� C.� Section 08300 - Special Doors.

 

��� D.� Section 08400 - Entrances and Storefronts.

 

��� E.� Section 08710 - Finish Hardware.

 

1.3 REFERENCES

Delete references from the list below that are not actually required by the text of the edited section.

��� A.� ANSI/DHI A115 Series - American National Standard Specifications for Steel Door and Frame Preparation for Hardware.

 

��� B.� BHMA A156.2 - American National Standard for Bored and Preassembled Locks and Latches.

 

��� C.� BHMA A156.13 - American National Standard for Mortise Locks & Latches;� Builders Hardware manufacturers Association.

 

��� D.� BHMA A156.18 - American National Standard for Materials and Finishes.

 

��� E.� Certification Listings;� Underwriters Laboratories, Inc.

 

��� F.� FF-H-106C - Hardware, Builders', Locks and Door Trim, General Specification for.

 

��� G.� The Americans With Disabilities Act of 1992.

 

1.4 SUBMITTALS

 

��� A.� Submit under provisions of Section 01300.

 

��� B.� Product Data:� Provide manufacturer's standard details and catalog data demonstrating compliance with referenced standards.� Provide installation instructions.

 

��� C.� Hardware Schedules:� Submit a schedule of products specified in this section coordinated with doors and hardware specified elsewhere.

�������

��� D.� Samples:� Submit 1 of each type of lockset.� Approved samples will be returned by the Architect for installation on the final openings of the Project.

 

��� E.� Contract Closeout Submittals:�

������� 1.� Schedule of keying, access codes, and openings.

Delete the following paragraph if not required.

������� 2.� Operation and maintenance materials.

 

1.5 DELIVERY, STORAGE, AND HANDLING

 

��� A.� Store products indoors in a secured area, and protect from moisture, construction traffic, and damage.

Delete the following Article if maintenance manual and materials are not required.� If retained, delete inapplicable products, and edit quantities to suit project requirements.

1.6 MAINTENANCE MATERIALS

 

��� A.� Deliver the following prior to Substantial Completion:

������� 1.� 2 each, operation manual for "Omnilock 50 Series."

������� 2.� 2 each, operation manual for "Omnilock 100, 300 & 500 Series."

������� 3.� 2 each, operation manual for "Omnilock 250 Series."

������� 4.� 1 each, lithium power-pak for use with "Omnilock 250 Series" control modules.

������� 5.� 1 each, informational and instructional VHS video tape for "Omnilock 250 Series."

������� 6.� 2 boxes, thermal paper for use with "WP4000 Wireless Printer" (6 rolls/box).

 

 

PART 2� PRODUCTS

 

2.1 MANUFACTURER

 

��� A.� Provide units fabricated by OSI Security Devices;� 657 North Pastoria Avenue, Sunnyvale, California;� 94086.� Telephone:� 408-720-0909.� Fax:� 408-720-9034.

Delete the following Article if not required.

2.2 OMNILOCK 50 SERIES LOCKSETS AND MODULES

 

��� A.� Provide "Omnilock 50 Series" locksets.

If exterior grade is required, retain 1 of the 2 following paragraphs.

 

If interior grade is required, retain the 3rd paragraph.

 

Edit, or include schedule showing required locations.

������� 1.� At exterior doors, provide weatherized outside/inside modules suitable for direct exposure to weather, and use at -40 to 129 degrees F.

������� 2.� Where scheduled, provide weatherized outside/inside modules suitable for direct exposure to weather, and use at -40 to 129 degrees F.

������� 3.� Provide drip-proof, splash and spray proof modules for interior use, except where weatherized outside modules are required.

Delete 1 of the 2 following paragraphs.� Silicon pads are standard.

������� 4.� Keypad:� 11 digit;� silicone rubber.

������� 5.� Keypad:� 11 digit;� stainless steel key buttons.

Delete 1 of the 2 following paragraphs.� Key cylinders are standard.

If I/C cores are required, specify cores and keys in the general hardware section (not furnished).

������� 6.� Key Cylinder:� Solid brass 6 pin cylinder with two brass keys.� Keyed 5 pin with Arrow "CS" keyway.

������� 7.� I/C Core:� For use with Arrow, Best, or Falcon 6 or 7 pin interchangeable cores.� (Cores specified elsewhere.)

Delete all but 1 of the following finishes or, if more than one are required, include of schedule showing required locations.�

 

626 finish is standard.

������� 8.� Finish:� 605-US3 (Polished Brass).

������� 9.� Finish:� 606-US4 (Satin Brass).

������� 10. Finish:� 612-US10 (Satin Bronze).

������� 11. Finish:� 613-US10B (Oil Rubbed Bronze).

������� 12. Finish:� 625-US26 (Polished Chrome).

������� 13. Finish:� 626-US26D (Satin Chrome).

 

��� B.� Module:

������� 1.� Material:� 14 gauge plated steel.

������� 2.� Finish:� Durable black epoxy powder coat.

 

��� C.� Access Levels:

������� 1.� Unlocked:� Free passage, handle unlocked.

������� 2.� Code Required:� Valid code required for entry.

������� 3.� Shutdown:� Master Code required for entry.

������� 4.� Anti-tamper:� Initially set after 3 consecutive invalid code entries. Additional key presses ignored for 10 seconds.

 

��� D.� Code Types:

������� 1.� 4 to 7 digits long as determined by the length of the Master code.

������� 2.� General User Code:� Allows access when access level is at Code Required and user group is enabled.� Up to 50 individual codes assignable into four user groups.

������� 3.� Supervisor Code:� Allows access when access level is at Code Required and user group is enabled or supervised.� Can restrict\enable general user codes in user group.

����������� a.� Supervisor privileges assignable to any of the 50 general user codes.

������� 4.� Service Code:� Variable lifetime code;� allows temporary (time limited) access to service personnel.

����������� a.� Quantity:� 1.

������� 5.� Submaster Code:� Programming and Entry code.

����������� a.� Quantity:� 3.

������� 6.� Master Code:� Programming, Entry code and Shutdown.

����������� a.� Quantity:� 1.

������� 7.� Audit Code:� Outputs Audit Log Report to optional printer.

����������� a.� Quantity:� 1.

 

��� E.� Other Functions:

������� 1.� Audit Log:� Retains last 250 transactions.

����������� a.� Record Format:� Date, Time, Identity, Transaction.

����������� b.� Transaction Types:� 18.

��� ������� c.� Clock resolution:� 1 minute with leap year correction.

������� 2.� Batteries:� 4 size 'AA' 1.5 volt alkaline.

����������� a.� Expected Life:� 5 years / 100,000 operations under normal operating conditions (40 to 80� degrees F room temperature).

����������� b.� Low Battery Warning:� LED's flash Green-Red-Red on each entry to alert users of a low battery condition. Normal operation shall continue for several hundred operations before entering Shutdown level.

����������� c.� Memory Retention:� Retain codes, programming, etc., for 1 minute with batteries removed to allow battery change.

 

��� F.� Lockset:

������� 1.� Lock Body:� Heavy duty, made in U.S.A.

������� 2.� Material:� Cold rolled steel and zinc dichromate finish for oxidation resistance with precision cast steel retractor.� 2-1/8-inch diameter bore.

������� 3.� Latch:� 2-3/4-inch backset standard, brass with 1/2-inch throw.� Housing is steel-zinc dichromate finish for oxidation resistance. 1-inch diameter bore.

������� 4.� Latch Face:� Brass, bronze or stainless steel face plates. 2-1/4 x 1-1/8 inches.

������� 5.� Strike Plate:� Square corner, 1-1/8 x 2-3/4 inches; T strike with 1-1/4-inch lip to center dimension; ANSI Standard A115 Series.

������� 6.� Handing:� Field reversible. Shipped right hand.

������� 7.� Door Thickness:� 1-3/4 inches standard.

������� 8.� Trim:� Through-bolted with independent springs for each lever.

������� 9.� Certification:�

����������� a.� ANSI Standard 156.2, Series 4000, Grade 1 requirements.�

����������� b.� FS FFH-106C, Type 161.

����������� c.� Levers:� The Americans With Disabilities Act of 1992.

����������� d.� UL listed for safety and fire (90 minutes).

������� 10. Function:� Lever retracts latchbolt from either side unless the outside (cylinder side) is electrically locked.� Unlocked from outside with valid code or by key.� Inside trim always free passage.

������� 11. Standard ANSI door preparation for cylindrical lockset with 2-3/4-inch backset and a door jamb not greater than 3/4 inch.� Two anti-rotation holes required.� Weatherized models:� Additional 1-inch diameter through-door bore.

Delete the following Article if not required.�

If retained, delete all but 1 of the Article headings, below.

2.3 OMNILOCK 100, 300, AND 500 SERIES LOCKSETS AND MODULES

 

2.4 OMNILOCK 100 SERIES LOCKSETS AND MODULES

 

2.5 OMNILOCK 300 SERIES LOCKSETS AND MODULES

 

2.6 OMNILOCK 500 SERIES LOCKSETS AND MODULES

Delete 1 of the 3 following paragraphs, or include a schedule of required locations of each type.

��� A.� Provide "Omnilock 100 Series" locksets.

������� 1.� General user code capacity:� 100.

 

��� B.� Provide "Omnilock 300 Series" locksets.

������� 1.� General user code capacity:� 300.

 

��� C.� Provide "Omnilock 500 Series" locksets.

������� 1.� General user code capacity:� 500.

If exterior grade is required, retain 1 of the 2 following paragraphs.

 

If interior grade is required, retain the 3rd paragraph.

 

Edit, or include schedule showing required locations.

������� 2.� At exterior doors, provide weatherized outside/inside modules suitable for direct exposure to weather, and use at -40 to 129 degrees F.

������� 3.� Where scheduled, provide weatherized outside/inside modules suitable for direct exposure to weather, and use at -40 to 129 degrees F.

������� 4.� Provide drip-proof, splash and spray proof modules for interior use, except where weatherized outside modules are required.

Delete 1 of the 2 following paragraphs.� Silicon pads are standard.

������� 5.� Keypad:� 11 digit;� silicone rubber.

������� 6.� Keypad:� 11 digit;� stainless steel key buttons.

Delete 1 of the 2 following paragraphs.� Key cylinders are standard.

 

If I/C cores are required, specify cores and keys in the general hardware section (not furnished).

������� 7.� Key Cylinder:� Solid brass 6 pin cylinder with two brass keys.� Keyed 5 pin with Arrow "CS" keyway.

������� 8.� I/C Core:� For use with Arrow, Best, or Falcon 6 or 7 pin interchangeable cores.� (Cores specified elsewhere.)

Delete all but 1 of the following finishes or, if more than one are required, include of schedule showing required locations.�

 

626 finish is standard.

������� 9.� Finish:� 605-US3 (Polished Brass).

������� 10. Finish:� 606-US4 (Satin Brass).

������� 11. Finish:� 612-US10 (Satin Bronze).

������� 12. Finish:� 613-US10B (Oil Rubbed Bronze).

������� 13. Finish:� 625-US26 (Polished Chrome).

������� 14. Finish:� 626-US26D (Satin Chrome).

 

��� D.� Module:

������� 1.� Material:� 14 gauge plated steel.

������� 2.� Finish:� Durable black epoxy powder coat.

 

��� E.� Access Levels:

������� 1.� Unlocked:� Free passage, handle unlocked.

������� 2.� Unlocked with code:� Unlocks after 'first code in'.

������� 3.� Code required:� Valid code required for entry.

������� 4.� Lockout:� Submaster or master required for entry.

������� 5.� Shutdown:� Master Code required for entry.

������� 6.� Anti-tamper:� Initially set after 3 consecutive invalid code entries.� Additional key presses ignored for 10 seconds.

 

��� F.� Code Types:

������� 1.� 4 to 9 digits long as determined by the length of the Master code.

������� 2.� General User Code:� Allows access when access level is at Code Required and user group is enabled.� Codes assignable into 4 user groups.

������� 3.� Supervisor Code:� Allows access when access level is at Code Required and user group is enabled or supervised.� Can restrict\enable general user codes in user group.

����������� a.� Supervisor privileges assignable to any of the general user codes.

������� 4.� Service Code:� Variable lifetime code;� allows temporary (time limited) access to service personnel.

����������� a.� Quantity:� 1.

������� 5.� Submaster Code:� Programming and Entry code.

����������� a.� Quantity:� 8.

������� 6.� Master Code:� Programming, Entry code and Shutdown.

����������� a.� Quantity:� 1.

������� 7.� Audit Code:� Outputs Audit Log Report to WP4000 wireless printer.

����������� a.� Quantity:� 1.

 

��� G.� Other Functions:

������� 1.� Audit Log:

Delete 2 of the 3 following paragraphs, unless more than 1 series is specified.

����������� a.� "100 Series":� Retain last 250 transactions.

����������� b.� "300 Series":� Retain last 500 transactions.

����������� c.� "500 Series":� Retain last 750 transactions.

����������� d.� Record Format:� Date, Time, Identity, Transaction.

����������� e.� Transaction Types:� 16.

������� 2.� Internal clock:�

����������� a.� Resolution:� 1 minute with leap year correction.

����������� b.� Daylight savings:� Automatic or manual corrections.

������� 3.� Time Schedule:� Sets access level and controls access for user groups automatically at preprogrammed times.

����������� a.� Capacity:� 144 schedules events.

����������� b.� User groups:� 4.

����������� c.� Holidays:� 32.

������� 4.� Facility Autocode:

����������� a.� Set up like access codes on multiple locks to accommodate any number of users.

������� 5.� Batteries:� 4 size 'AA' 1.5 volt alkaline.

����������� a.� Expected Life:� 5 years / 100,000 operations under normal operating conditions (40 to 80� degrees F room temperature).

����������� b.� Low Battery Warning:� LED's flash Green-Red-Red on each entry to alert users of a low battery condition. Normal operation shall continue for several hundred operations before entering Shutdown level.

����������� c.� Memory Retention:� Retain codes, programming, etc., for 1 minute with batteries removed to allow battery change.

 

��� H.� Lockset:

������� 1.� Lock Body:� Heavy duty, made in U.S.A.

������� 2.� Material:� Cold rolled steel and zinc dichromate finish for oxidation resistance with precision cast steel retractor.� 2-1/8-inch diameter bore.

������� 3.� Latch:� 2-3/4-inch backset standard, brass with 1/2-inch throw.� Housing is steel-zinc dichromate finish for oxidation resistance. 1-inch diameter bore.

������� 4.� Latch Face:� Brass, bronze or stainless steel face plates. 2-1/4 x 1-1/8 inches.

������� 5.� Strike Plate:� Square corner, 1-1/8 x 2-3/4 inches; T strike with 1-1/4-inch lip to center dimension; ANSI Standard A115 Series.

������� 6.� Handing:� Field reversible. Shipped right hand.

������� 7.� Door Thickness:� 1-3/4 inches standard.

������� 8.� Trim:� Through-bolted with independent springs for each lever.

������� 9.� Certification:�

����������� a.� ANSI Standard 156.2, Series 4000, Grade 1 requirements.�

����������� b.� FS FFH-106C, Type 161.

��� ������� c.� Levers:� The Americans With Disabilities Act of 1992.

����������� d.� UL listed for safety and fire (90 minutes).

������� 10. Function:� Lever retracts latchbolt from either side unless the outside (cylinder side) is electrically locked.� Unlocked from outside with valid code or by key.� Inside trim always free passage.

������� 11. Standard ANSI door preparation for cylindrical lockset with 2-3/4-inch backset and a door jamb not greater than 3/4 inch.� Two anti-rotation holes required.� Weatherized models:� Additional 1-inch diameter through-door bore.

Delete the following Article if not required.

2.7 OMNILOCK 250 SERIES CYLINDRICAL LOCKSETS

 

��� A.� Provide "Omnilock 250 Series" heavy duty cylindrical locksets.

Available trim/cylinder/core options are listed in the next 3 paragraphs.� Contact the factory for availability of Schlage "Primus" cylinders (not listed).

 

Delete trim/cylinder/core combinations that are not required.

��� B.� Cylinders and Trim:� Solid brass 6 pin cylinder with two brass keys.� Keyed 5 pin (KD) with Schlage "C" keyway.

������� 1.� Athens (ATH).

������� 2.� Rhodes (RHO).

������� 3.� Sparta (SPA).

������� 4.� Luna (LUN).

������� 5.� Orbit (ORB).

������� 6.� Plymouth (PLY).

������� 7.� Tulip (TUL).

 

��� C.� Trim:� "Best" adaptor knob.

������� 1.� For use with Arrow, Best, or Falcon interchangeable cores.� (Cores specified elsewhere.)

 

��� D.� I/C Cores and Trim:� Provide Schlage I/C core cylinders.

������� 1.� Athens (ATH).

������� 2.� Rhodes (RHO).

������� 3.� Sparta (SPA).

 

��� E.� Finish:

Delete all but 1 of the following finishes or, if more than one are required, include of schedule showing required locations.�

 

626 finish is standard.

������� 1.� Finish:� 605-US3 (Polished Brass).

������� 2.� Finish:� 606-US4 (Satin Brass).

������� 3.� Finish:� 612-US10 (Satin Bronze).

������� 4.� Finish:� 613-US10B (Oil Rubbed Bronze).

������� 5.� Finish:� 625-US26 (Polished Chrome).

������� 6.� Finish:� 626-US26D (Satin Chrome).

 

��� F.� Locksets:

������� 1.� Lock Body:� Heavy duty commercial grade chassis.� Steel mechanism, zinc dichromated.

������� 2.� Material:� Cold rolled steel and zinc dichromate finish for oxidation resistance with precision cast steel retractor.� 2-1/8-inch diameter bore.

������� 3.� Latch:� 2-3/4-inch backset standard, brass with 1/2-inch throw.� Housing is steel-zinc dichromate finish for oxidation resistance. 1-inch diameter bore.

������� 4.� Latch Face:� Brass, bronze or stainless steel face plates. 2-1/4 x 1-1/8 inches.

������� 5.� Strike Plate:� Square corner, 1-1/8 x 2-3/4 inches; T strike with 1-1/8-inch lip to center dimension; ANSI Standard A115 Series.

������� 6.� Handing:� Field reversible. Shipped right hand.

������� 7.� Door Thickness:� 1-3/4 inches standard to 2 inches.

������� 8.� Trim:� Through-bolted with independent springs for each lever.

������� 9.� Certification:�

����������� a.� ANSI Standard 156.2, Series 4000, Grade 1 requirements.�

����������� b.� FS FFH-106C, Type 161.

����������� c.� Levers:� The Americans With Disabilities Act of 1992.

����������� d.� UL listed for safety and fire (20 minutes).

������� 10. Function:� Lever retracts latchbolt from either side unless the outside (cylinder side) is electrically locked.� Unlocked from outside with 7-digit code or by key.� Inside trim always free passage.

������� 11. Standard ANSI door preparation for cylindrical lockset with 2-3/4-inch (or greater) backset and a door jamb not greater than 3/4 inch.� Two anti-rotation holes required.�

Delete the following Article if not required.

2.8 OMNILOCK 250 SERIES MORTISE LOCKSETS

 

��� A.� Provide "Omnilock 250 Series" mortise locksets.

Delete 1 of the 2 following paragraphs or, if both functions are required, edit to suit project requirements or include a schedule of locations.

������� 1.� Storeroom function:� Latchbolt retracted by knob or lever from either side unless outside is locked electrically.� Unlock from outside with a 7 digit code or by key. Inside trim always free passage.

������� 2.� Entrance function:� 1-inch deadbolt.� Latch and deadbolt retracted simultaneously by knob or lever from either side unless outside is locked electrically.� Unlock from outside with a 7 digit code or by key.� Inside trim always free passage.� Deadbolt thrown or retracted by key or thumbturn.� Auxiliary latch deadlocks latchbolt when door is closed.

Delete all but 1 lever and knob trim styles, below.

��� B.� Lever Trim Style:

������� 1.� Style 03.

������� 2.� Style 05.

������� 3.� Style 06.

������� 4.� Style 27.

������� 5.� Style 12.

������� 6.� Style 17.

������� 7.� Style 72.

������� 8.� Style 73.

 

��� C.� Knob Trim Style:

������� 1.� Style 41.

������� 2.� Style 42.

 

��� D.� Retrofit:� Less finished trim.

"B" size rose trim is also available.� Contact the factory.

��� E.� Rose Trim:� Schlage A rose standard (2-1/8-inch diameter, wrought).

 

��� F.� Finish:

Delete all but 1 of the following finishes or, if more than one are required, include of schedule showing required locations.�

 

626 finish is standard.

������� 1.� Finish:� 605-US3 (Polished Brass).

������� 2.� Finish:� 606-US4 (Satin Brass).

������� 3.� Finish:� 612-US10 (Satin Bronze).

������� 4.� Finish:� 613-US10B (Oil Rubbed Bronze).

������� 5.� Finish:� 625-US26 (Polished Chrome).

������� 6.� Finish:� 626-US26D (Satin Chrome).

 

��� G.� Keying:

Retain only the 1st paragraph, below, for standard cylinders.

Retain the 1st and 2nd for I/C cores.

Retain only the 3rd paragraph if cylinders will be furnished elsewhere.

 

Contact the factory for availability of Schlage "Primus" cylinders (not listed).

������� 1.� 6 pin Schlage 1-3/8 to 1-1/4-inch mortise cylinder keyed 5 pin with "C" keyway (KD) with 2 keys.

������� 2.� Provide Schlage interchangeable core type mortise cylinders.

������� 3.� Furnish locks less cylinders.

 

��� H.� Lockset:

������� 1.� Lock Body:� Heavy duty commercial grade mortise chassis.

������� 2.� Latchbolt:� 3/4-inch throw, stainless steel.

������� 3.� Deadbolt:� 1-inch throw, stainless steel.

������� 4.� Door Thickness:� 1-3/4 inches standard to 2 inches.

������� 5.� Backset:� 2-3/4 inches.

������� 6.� Armored Front:� 1-1/4 x 8 x 7/32 inches.

������� 7.� Mortise Case Size:� 4-7/16 x 6-1/16 x 1 inches.

������� 8.� Strike Plate:� Square corner, 4-7/8 inches.

������� 9.� Handing:� Field reversible. Shipped right hand.

������� 10. Certification:�

����������� a.� ANSI Standard 156.13, 1000, Grade 1 Operational requirements.

����������� b.� Levers:� "The Americans With Disabilities Act of 1992".�

����������� c.� Lockset:� UL listed for safety and fire (20 minutes) by Underwriters Laboratories Inc.

If 250 series cylindrical or mortise locks are retained above, retain the following Article;� otherwise delete.

2.9 OMNILOCK 250 SERIES MODULES

 

��� A.� Module:

������� 1.� Keypad:� 11 digit;� metal-buttons with steel backplate.

������� 2.� Material:� 14 gauge plated steel.

������� 3.� Finish:� Durable black epoxy powder coat.

Delete the following paragraph if not required.

������� 4.� "SWS-1 Spy Shield":� Limits viewing angle of keypad.

 

��� B.� Access Levels:

������� 1.� Unlocked:� Free passage, handle unlocked.

������� 2.� Code Required:� Valid User code required for entry.

������� 3.� Lockout:� User codes locked out, Extended Users gain entry.�

������� 4.� Shutdown:� Only Master Code will operate lock.

������� 5.� Access Levels overridden manually by an extended-user or automatically by the Time Schedule.

 

��� C.� Code Types:

������� 1.� User Code:� Allows access when level is at 2-Code Required.

����������� a.� Up to 250 individual user codes assignable.

����������� b.� 7-digit user code picked manually or, randomly assigned by the lock using the AutoCode feature.

������� 2.� Extended User Code:

����������� a.� Allow additional access when level is 3-Lockout.

����������� b.� Allow a new access level to be set without a printer.

����������� c.� Any of the 250 users convertible to Extended-User.

����������� d.� 8-digit access code.

������� 3.� Submaster Code:� Programs and audits the Omnilock with selectable restrictions on menu access.

����������� a.� Up to 5 unique Submaster codes.

����������� b.� 7-digit access code.

������� 4.� Master Code:� Programs and audits the module.

����������� a.� Quantity:� 1.

����������� b.� 7-digit code.

 

��� D.� Attempt Counter:� Records illegal access code attempts;� locks out a particular user code after a preset number of attempts.� Code reactivated either automatically, or manually by an administrator.

 

��� E.� Audit Log:� Retains the last 250 audit records.

������� 1.� Record Format:� Day, Date, Time, Identity, Transaction.

������� 2.� Transaction Types:� 6.

 

��� F.� Internal Clock:

������� 1.� Resolution:� 1 minute.

������� 2.� Programmable daylight savings corrections.

 

��� G.� Time Schedule:

������� 1.� Number of Schedules per week:� 7 (1 per day).

������� 2.� Number of Access Level changes per day:� 8.

������� 3.� Number of holidays per year:� 32 (overrides daily schedule).

������� 4.� Number of Holiday Schedules:� 2.

 

��� H.� Facility Autocode:

������� 1.� Set up like access codes on multiple locks to accommodate any number of users.

 

��� I.� "OMBR-23" Power Pak:

������� 1.� Type:� UL-Listed cells.

������� 2.� Connector:� 3-pin gold plated.

������� 3.� Expected Life:� S years/50,000 Cycles.

������� 4.� Low Battery Indication:� 2 separate warnings.

����������� a.� Print battery level from BAT:� 5(new) to BAT:� 0(replace); change to Access Level 4-Shutdown if BAT:� 0 occurs.

����������� b.� When BAT:� 1 (warning) occurs, flash a yellow light instead of a green light for each entry.

Delete the following Article if not required.� The wall mount module is designed to control electromagnetic or electromechanical locks (not furnished).

2.10��� WALL MOUNT SYSTEM

 

��� A.� Provide "Omnilock OM250TL-WMS Wall Mount System".

������� 1.� Electromagnetic or electromechanical lock:� Specified elsewhere.

 

��� B.� Module:

������� 1.� Material:� 14 gage plated steel.

������� 2.� Finish:� Durable black epoxy powder coat.

������� 3.� Keypad:� Eleven digit metal-button keypad with steel backplate for vandal resistance.

 

��� C.� Operation:� 1 of 250 individual 7-digit access codes is entered on the keypad to cause the unit to flash green, activate a relay for 1 to 30 seconds, record the date and time, and identify the user.� The unit will then flash red and de-activate the relay.

 

��� D.� Mounting:� Plate mounts to front surface of wall.� Unit locked to the mounting plate with high-security keylock.

 

��� E.� Control Relay:� Latching-style low power relay that uses no power to remain indefinitely locked or unlocked.

 

��� F.� Internal Power:� Easily replaceable Lithium Power-Pak (included) for 5 Year/50,000 use operation.

The unit below is optional for use with the Omnilock 50 series and is REQUIRED for programming all other Omnilocks.� One unit will work with any number of Omnilocks.

2.11��� WIRELESS PRINTER

 

��� A.� Provide "Omnilock WP4000 Wireless Printer".

������� 1.� Dimensions:� 3-1/2 inches wide x 7 inches long.

������� 2.� Interface:�� Infrared light beam.

������� 3.� Activation:� By holding above an Omnilock and entering a Master or Submaster code.

������� 4.� Distance:� 1 to 4 inches above the Omnilock.

������� 5.� Controls:� 3 (Power On/Off, Print Contrast and Paper Feed).

������� 6.� Printing:� Prints all Omnilock reports and programming menus.

������� 7.� Paper:� 24 character wide black-print thermal paper;� provide 1 roll.

������� 8.� Batteries:� 4 AA alkaline batteries;� provide 1 set.

 

 

PART 3� EXECUTION

 

3.1 EXAMINATION

 

��� A.� Verify that openings are complete and ready to receive locksets.

 

3.2 PREPARATION

 

��� A.� Meet with Owner to determine coding groups and other access requirements.

 

3.3 INSTALLATION

 

��� A.� Install locksets and modules in accordance with manufacturer's instructions.

 

��� B.� Program modules in accordance with requirements established by Owner.

 

3.4 DEMONSTRATION

 

��� A.� Instruct Owner's representative in the programming and operation of modules.

 

��� B.� Instruct Owner's representative in the removal and reinstallation of modules and locksets, battery replacement, and other maintenance operations.

 

3.5 ADJUST AND CLEAN

 

��� A.� Verify that units are adjusted for smooth and proper operation.

 

��� B.� Clean surfaces of soil or other marks.

 

��� C.� Remove scrap and debris, and leave the site in a clean condition.

 

 

����������������������� Back to SPECDISK Table of Contents

---

sorabji.com > foundcrap > found floppies > specdisk