Exterior Painting

�� SECTION 09910

�� EXTERIOR PAINTING

�� 395 Oyster Point Boulevard

�� Suite 350

�� Telephone:� 415-871-6060

PART 1� GENERAL

1.1 SECTION INCLUDES

�� A.� Surface preparation and field application of paints on exterior substrates.

�� B.� Surface preparation and field application of stains on exterior substrates.

1.2 RELATED SECTIONS

�� A.� Section _____ - _________________:� Pavement markings.

�� B.� Section 09920 - Interior Painting.

�� C.� Section 09960 - Special Coatings.

�� D.� Section _____ - __________________:� Shop finished exterior cladding system.

1.3 REFERENCES

�� A.� ASTM D 16 - Standard Terminology Relating to Paint, Varnish, Lacquer, and Related Products.

1.4 DEFINITIONS

�� A.� Conform to definitions of terms in ASTM D 16 in interpreting requirements of this specification section.

1.5 SUBMITTALS

�� A.� Submit under provisions of Section 01300.

�� B.� Product Data:� Provide manufacturer's printed product data on all coatings specified, including preparation and application instructions.

�� C.� Selection Samples:� Provide two sets of samples not less than one inch by two inches in size illustrating range of colors and textures available for each finishing product specified.

�� D.� Verification Samples:� Provide two samples of not less than six inches square illustrating selected colors and textures for each color specified.

1.6 DELIVERY, STORAGE, AND HANDLING

�� A.� Deliver, store, and protect products under provisions of Section 01600.

�� B.� Deliver products to site in sealed and labeled containers.� Labels shall include manufacturer's name, type of coating, brand name, lot number, estimated coverage, surface preparation requirements, drying time, cleanup instructions, color designation, and instructions for mixing.

�� C.� Store paint products in covered, ventilated area at minimum ambient temperature of 45 degrees F and maximum ambient temperature of 90 degrees F.

1.7 ENVIRONMENTAL REQUIREMENTS

�� A.� Do not apply products of this section outside acceptable range of conditions as specified by paint manufacturer.�

�� B.� Do not apply coatings during rain or snow or when humidity is in excess of manufacturer's recommended limit.

1.8 EXTRA MATERIALS

�� A.� Furnish extra materials under provisions of Section 01700.

�� B.� Deliver to Owner 1 gallon of each finish paint in each color required for Project.

�� 1.� Mark each container with color and locations where paint was used, without obscuring manufacturer's label.

PART 2� PRODUCTS

2.1 MANUFACTURER

�� A.� Provide products manufactured by Fuller O'Brien Paints, headquartered at 395 Oyster Point Boulevard, Suite 350, South San Francisco, CA� 94080.

�� B.� Substitutions will not be acceptable.

2.2 MATERIALS

�� A.� Coatings:� Ready mixed, except for field catalyzed coatings; having good flow and brushing properties and consistent drying or curing behavior, free of sags and streaks.

�� B.� Accessory Materials:� Linseed oil, turpentine, paint thinners and other materials recommended by coatings manufacturer as necessary to achieve finishes specified.

�� C.� Patching and Surface Preparation:� Latex fillers as recommended by coatings manufacturer.

PART 3� EXECUTION

3.1 EXAMINATION

�� A.� Verify that site environmental conditions are appropriate and substrates are in proper condition to receive work of this section.

�� B.� Verify that shop applied primers are compatible with specified finish coats.

�� C.� Measure moisture content of surfaces using an electronic moisture meter.� Do not begin application of coatings unless moisture content of surfaces is below the following maximum values:

�� 1.� Gypsum soffits:� 12 percent.

�� 2.� Plaster:� 12 percent.

�� 3.� Masonry surfaces:� 12 percent.

�� 4.� Wood surfaces:� 15 percent.

�� 5.� Vertical concrete surfaces:� 12 percent.

�� 6.� Horizontal concrete surfaces:� 8 percent.

3.2 PREPARATION

�� A.� Remove or mask electrical plates, hardware, light fixture trim, and similar fittings prior to beginning painting operations.

�� B.� Correct defects and clean surfaces affecting work of this section.� Remove existing coatings that are flaking or otherwise in unacceptable condition to receive paint.

�� C.� Seal with shellac or other coating acceptable to paint manufacturer any marks or defects that might bleed through paint finishes.

�� D.� Remove mildew from impervious surfaces by scrubbing with solution of trisodium phosphate and bleach.� Rinse with clean water and allow substrate to dry.

�� E.� Concrete and Masonry Surfaces:� Remove dirt, loose mortar, scale, salts, alkalies, and other detrimental substances.� Remove oils and grease with solution of trisodium phosphate;� rinse well and allow to dry.

�� F.� Concrete Floors:� Remove dirt and grease, acid etch, and rinse with clear water.

�� G.� Plaster and Stucco:� Fill hairline cracks, small holes, and imperfections with patching compound, then smooth patches to match adjacent surfaces.

�� H.� Exterior Wood for Opaque Finish:� Remove dirt and foreign matter. Patch knots, pitch pockets, and other surface imperfections with patching compound and seal with sealer recommended by paint manufacturer.

�� I.� Exterior Wood for Transparent Finish:� Remove dirt and foreign matter. Seal knots and pitch pockets with sealer recommended by stain manufacturer.� Fill nail holes and other surface imperfections with tinted calking compound after sealer has been applied.

�� J.� Wood Doors:� Seal top and bottom edges with specified primer.

�� K.� Metal Doors:� Seal top and bottom edges with specified primer.

�� L.� Galvanized Metal Surfaces:� Remove oils and wash with solvent.

�� M.� Aluminum Surfaces:� Remove surface contamination by steam or high pressure water.� Remove oxidation by acid etching and solvent washing.� Apply specified primer as soon as cleaned surfaces are dry.

3.3 APPLICATION

�� A.� Apply paint products in accordance with manufacturer's printed instructions.� Do not apply coatings to surfaces that are not dry.

�� B.� Apply each coat to uniform thickness and finish, with each coat slightly darker than preceding coat.� Allow each coat to dry thoroughly before applying next coat.

�� C.� Sand wood and metal surfaces lightly between coats. Vacuum surfaces free of loose particles prior to application of next coat.

3.4 CLEANING AND PROTECTION

�� A.� Keep project premises free of painting-related debris.� Collect material that may constitute a fire hazard, place in closed metal containers, and remove daily from site.

�� B.� Protect work adjacent to painting operations from paint spatters and spills.� Immediately remove paint that falls on finished surfaces not scheduled to receive paint, using materials and techniques that will not damage affected surfaces.

3.5 SCHEDULE

�� A.� Poured or Precast Concrete, Portland Cement Plaster, Stucco:

�� 1.� Flat Finish:

�� a.� Acrylic Latex:

�� 1)� 1 coat 220-17 Pigmented Concrete and Masonry Primer-Sealer.

�� 2)� 1 or 2 coats 262-XX 100 percent Acrylic Flat,

�� b.� Acrylic Latex Accent Colors:

�� 1)� 1 coat 220-17 Pigmented Concrete and Masonry Primer-Sealer.

�� 2)� 2 coats 609-XX Ultra Color Interior/Exterior Latex Flat.

�� c.� Elastomeric Coating:

�� 1)� 1 coat 9410 Bond Coat Primer.

�� 2)� 2 coats 9600 Tekmafilm Elastomeric Coating.

�� 2.� Clear, Water Repellent Finish:

�� a.� Waterborne:

�� 1)� 1 coat 9340 Ful-Seal Regular Water Repellent.

�� B.� Concrete Block Brick and Pumice Block:

�� 1.� Flat Finish:

�� a.� Acrylic Latex:

�� 1)� 2 coats 262-XX 100 percent Acrylic Flat.

�� b.� Acrylic Latex Accent Colors:

�� 1)� 2 coats 609-XX Ultra Color Interior/Exterior Latex Flat.

�� c.� Elastomeric Coating:

�� 1)� 1 coat 9410 Bond Coat Primer.

�� 2)� 2 coats 9600 Tekmafilm Elastomeric Coating.

�� 2.� Clear, Water Repellent Finish:

�� a.� Waterborne:

�� 1)� 1 coat 9340 Ful-Seal Regular Water Repellent.

�� C.� Concrete Block, Split-Face Block:

�� 1.� Flat, Smooth Finish:

�� a.� Acrylic Latex:

�� 1)� 1 coat 280-00 Latex Block Filler.

�� 2)� 1 or 2 coats 262-XX 100 percent Acrylic Flat.

�� b.� Acrylic Latex Accent Colors:

�� 1)� 1 coat 280-00 Latex Block Filler.

�� 2)� 2 coats 609-XX Ultra Color Interior/Exterior Latex Flat.

�� c.� Elastomeric Coating:

�� 1)� 1 coat 9610 Fibrated Elastomeric Block Filler.

�� 2)� 1 or 2 coats 9600 Tekmafilm Elastomeric Coating.

�� 2.� Natural Texture:

�� a.� Acrylic Latex:

�� 1)� 2 coats 262-XX 100 percent Acrylic Flat.

�� b.� Acrylic Latex Accent Colors:

�� 1)� 2 coats 609-XX Ultra Color Interior/Exterior Latex Flat.

�� 3.� Clear, Water Repellent Finish:

�� a.� Waterborne:

�� 1)� 1 coat 9340 Ful-Seal Regular Water Repellent.

�� D.� Concrete Floors and Decking:

�� 1.� Gloss Finish:

�� a.� Alkyd:

�� 1)� 1 coat 630-XX Porch and Floor Enamel (thinned 100 percent).

�� 2)� 1 coat 630-XX Porch and Floor Enamel.

�� 3)� Add sand or pumice to final coat for non-skid surface.

�� 2.� Satin Finish:

�� a.� Acrylic Latex:

�� 1)� 2 coats 631-XX Latex Floor Enamel.

�� 2)� Add sand or pumice to final coat for non-skid surface.

�� 3.� Clear, Water Repellent Finish:

�� a.� Waterborne:

�� 1)� 1 coat 9340 Ful-Seal Regular Water Repellent.

�� 2)� Add sand or pumice to final coat for non-skid surface.

�� E.� Smooth Wood Siding:

�� 1.� Gloss Finish:

�� a.� Alkyd:

�� 1)� 1 coat 220-23 Exterior Wood Primer.

�� 2)� 1 or 2 coats 260-XX House & Trim Paint.

Select final coating above or below.

�� 3)� 1 or 2 coats 298-XX VOC Compliant House & Trim Paint.

�� b.� Acrylic Latex:

�� 1)� 1 coat 220-23 Exterior Wood Primer.

�� 2)� 1 or 2 coats 669-XX Weather King II House & Trim Paint.

�� 2.� Semi-Gloss Finish:

�� a.� Acrylic Latex:

�� 1)� 1 coat 220-23 Exterior Wood Primer.

�� 2)� 1 or 2 coats 664-XX Weather King II House & Trim Paint.

�� 3.� Flat Finish:

�� a.� Latex:

�� 1)� 1 coat 220-23 Exterior Wood Primer.

�� 2)� 1 or 2 coats 667-XX Ful-Stain Flat Latex House Paint.

�� b.� Alkyd:

�� 1)� 1 or 2 coats 665-XX Ful-Stain Solid Coat Stain.

�� 4.� Semi-Transparent Stain Finish:

�� a.� Alkyd/Oil:

�� 1)� 1 or 2 coats 645-XX Ful-Stain Semi-Transparent Stain.

Select coating system above or below.

�� 2)� 1 or 2 coats VOC Compliant 645-7X Ful-Stain Semi-Transparent Stain.

�� F.� Rough Lumber, Shingles, and Plywood Siding:

�� 1.� Flat Solid Stain Finish:

�� a.� Latex:

�� 1)� 1 or 2 coats 667-XX Ful-Stain Flat Latex House Paint.

�� b.� Alkyd:

�� 1)� 1 or 2 coats 665-XX Ful=Stain Solid Coat Stain.

�� 2.� Semi-Transparent Stain Finish:

�� a.� Alkyd/Oil:

�� 1)� 1 or 2 coats 645-XX Ful-Stain Semi-Transparent Stain.

Select coating system above or below.

�� 2)� 1 or 2 coats VOC Compliant 645-7X Ful-Stain Semi-Transparent Stain.

�� G.� Brushed or Abraded Plywood:

�� 1.� Semi-Transparent Stain Finish:

�� a.� Alkyd/Oil:

�� 1)� 1 or 2 coats 645-XX Ful-Stain Semi-Transparent Stain.

�� H.� Hardboard Siding, Cement Shingles, Asbestos Shingles:

�� 1.� Semi-Gloss Finish:

�� a.� Acrylic Latex:

�� 1)� 1 coat 668-50 Weather King II Exterior Primer and Stain Blocker.

�� 2)� 2 coats 664-XX Weather King 100 percent House & Trim Paint.

�� 2.� Eggshell Finish:

�� a.� Latex:

�� 1)� 1 coat 668-50 Weather King II Exterior Primer and Stain Blocker.

�� 2)� 2 coats 261-XX Eggshell Latex House & Trim Paint.

�� I.� Wood Trim, Doors, Facia, Windows and Shutters:

�� 1.� Gloss Finish:

�� a.� Alkyd:

�� 1)� 1 coat 220-23 Exterior Wood Primer.

�� 2)� 1 or 2 coats 660-XX House & Trim Paint.

Select coating above or below.

�� 3)� 1 or 2 coats 298-XX VOC Compliant House & Trim Paint.

�� b.� Acrylic Latex:

�� 1)� 1 coat 220-23 Exterior Wood Primer.

�� 2)� 1 or 2 coats 669-XX Weather King II House & Trim Paint.

�� 2.� Semi-Gloss Finish:

�� a.� Alkyd Accent Colors:

�� 1)� 1 coat 220-23 Exterior Wood Primer.

�� 2)� 2 coats 619-XX Ultra Color Interior/Exterior Alkyd Semi-Gloss Enamel.

�� b.� Acrylic Latex:

�� 1)� 1 coat 220-23 Exterior Wood Primer.

�� 2)� 1 or 2 coats 664-XX Weather King Latex House & Trim Paint.

�� c.� Acrylic Latex Accent Colors:

�� 1)� 1 coat 220-23 Exterior Wood Primer.

�� 2)� 2 coats 639-XX Ultra Color Interior/Exterior Latex Semi-Gloss.

�� 3.� Eggshell Finish:

�� a.� Latex:

�� 1)� 1 coat 220-23 Exterior Wood Primer.

�� 2)� 1 or 2 coats 261-XX Eggshell Sheen Latex House and Trim Paint.

�� 4.� Clear Gloss Finish:

�� a.� Spar Varnish:

�� 1)� 1 coat 650-08 Master Marine Spar Varnish (thinned 10 percent).

�� 2)� 1 or 2 coats 650-08 Exterior Master Marine Spar Varnish.

�� b.� Polyurethane:

Select one of the two primers below.

�� 1)� 1 coat 652-00 PenThane Gloss (thinned 10 percent).

�� 2)� 1 coat 653-00 Low VOC PenThane Gloss.

�� 3)� 1 or 2 coats 652-00 PenThane Gloss.

�� 4)� 1 or 2 coats 653-00 Low VOC PenThane Gloss.

��

�� J.� Covered or Protected Wood Flooring and Decking:

�� 1.� Back Prime with specified primer before installation.

�� 2.� Gloss Finish:

�� a.� Alkyd:

�� 1)� 1 coat 630-XX Porch and Floor Enamel (thinned 10 percent).

�� 2)� 1 coat 630-XX Porch and Floor Enamel.

�� 3.� Eggshell Finish:

�� a.� Acrylic Latex:

�� 1)� 2 coats 631-XX Latex Floor Enamel.

�� K.� Exposed Wood Flooring and Decking:

�� 1.� Semi-Transparent Finish:

�� a.� Alkyd/Oil:

�� 1)� 1 coat 645-XX Ful-Stain Semi-Transparent Stain.

Select coating above or below.

�� 2)� 1 coat 645-7X VOC Compliant Ful-Stain Semi-Transparent Stain.

�� L.� Shop-Primed Ferrous Metal:

�� 1.� Clean all bare and abraded areas to bright, bare metal and touch up with 621-04 Blox-Rust.

�� 2.� Gloss Finish:

�� a.� Alkyd:

�� 1)� 1 coat 621-04 Blox-Rust Alkyd Metal Primer.

�� 2)� 1 or 2 coats 660-XX House & Trim Paint.

�� 3)� 1 or 2 coats 298-XX VOC Compliant House & Trim Paint.

�� b.� Acrylic Latex:

�� 1)� 1 coat 621-04 Blox-Rust Alkyd Metal Primer.

�� 2)� 1 or 2 coats 669-XX Weather King II House & Trim Paint.

�� 3.� Semi-Gloss Finish:

�� a.� Acrylic Latex:

�� 1)� 1 coat 621-04 Blox-Rust Alkyd Metal Primer.

�� 2)� 2 coats 664-XX Weather King Latex House & Trim Paint.

�� b.� Alkyd Accent Colors:

�� 1)� 1 coat 621-04 Blox-Rust Alkyd Metal Primer.

�� 2)� 2 coats 619-XX Ultra Color Interior/Exterior Alkyd Semi-Gloss Enamel.

�� c.� Acrylic Latex Accent Colors:

�� 1)� 1 coat 621-04 Blox-Rust Alkyd Metal Primer.

�� 2)� 2 coats 639-XX Ultra Color Interior/Exterior Latex Semi-Gloss.

�� 4.� Eggshell Finish:

�� a.� Latex:

�� 1)� 1 coat 621-04 Blox-Rust Alkyd Metal Primer.

�� 2)� 1 or 2 coats 261-XX Eggshell Sheen Latex House & Trim Paint.

�� 5.� Flat Finish:

�� a.� Acrylic Latex:

�� 1)� 1 coat 621-04 Blox-Rust Alkyd Metal Primer.

�� 2)� 1 or 2 coats 262-XX 100 percent Acrylic Flat.

�� b.� Acrylic Latex Accent Colors:

�� 1)� 1 coat 621-04 Blox-Rust Alkyd Metal Primer.

�� 2)� 2 coats 609-XX Ultra Color Interior/Exterior Latex Flat.

�� M.� Galvanized Metal:

�� 1.� Acid etch galvanized surfaces that have not weathered at least six months prior to beginning painting operations.

�� 2.� Gloss Finish:

�� a.� Alkyd Finish: