sorabji.com > foundcrap > found floppies > specdisk


������������������������ SECTION 09920

 

���������������������� INTERIOR PAINTING

This section includes surface preparation, priming, and painting or staining of interior surfaces that are commonly field coated.� This section should be edited to remove requirements for surfaces and coating systems not needed on a particular project.

 

All coatings included in this section are manufactured by Fuller O'Brien Paints, headquartered at the following address:

��� 395 Oyster Point Boulevard

��� Suite 350

��� South San Francisco, CA� 94080

��� Telephone:� 415-871-6060

 

A key element of this specification is the schedule at the end, organized by substrate and finish requirements.� We recommend that you begin the editing of this section with the schedule, deleting all systems not needed on the project, before modifying the rest of the document.

 

PART 1� GENERAL

 

1.1 SECTION INCLUDES

 

��� A.� Surface preparation and field application of paints on interior substrates.

 

��� B.� Surface preparation and field application of stains on interior substrates.

 

1.2 RELATED SECTIONS

 

��� A.� Section _____ - _________________:� Pavement markings.

 

��� B.� Section 09910 - Exterior Painting.

 

��� C.� Section 09960 - Special Coatings.

 

��� D.� Section _____ - __________________:� Shop finished cabinetry and paneling.

 

1.3 REFERENCES

 

��� A.� ASTM D 16 - Standard Terminology Relating to Paint, Varnish, Lacquer, and Related Products.

 

1.4 DEFINITIONS

 

��� A.� Conform to definitions of terms in ASTM D 16 in interpreting requirements of this specification section.

 

1.5 SUBMITTALS

 

��� A.� Submit under provisions of Section 01300.

 

��� B.� Product Data:� Provide manufacturer's printed product data on all coatings specified, including preparation and application instructions.

 

��� C.� Selection Samples:� Provide two sets of samples not less than one inch by two inches in size illustrating range of colors and textures available for each finishing product specified.

 

��� D.� Verification Samples:� Provide two samples of not less than six inches square illustrating selected colors and textures for each color specified.

 

1.6 DELIVERY, STORAGE, AND HANDLING

 

��� A.� Deliver, store, and protect products under provisions of Section 01600.

 

��� B.� Deliver products to site in sealed and labeled containers.� Labels shall include manufacturer's name, type of coating, brand name, lot number, estimated coverage, surface preparation requirements, drying time, cleanup instructions, color designation, and instructions for mixing.

 

��� C.� Store paint products in covered, ventilated area at minimum ambient temperature of 45 degrees F and maximum ambient temperature of 90 degrees F.

 

1.7 ENVIRONMENTAL REQUIREMENTS

 

��� A.� Do not apply products of this section outside acceptable range of conditions as specified by paint manufacturer.�

 

��� B.� Do not apply coatings when humidity is in excess of manufacturer's recommended limit.

 

1.8 EXTRA MATERIALS

 

��� A.� Furnish extra materials under provisions of Section 01700.

 

��� B.� Deliver to Owner 1 gallon of each finish paint in each color required for Project.

������� 1.� Mark each container with color and room names or numbers where paint was used, without obscuring manufacturer's label.

 

 

PART 2� PRODUCTS

 

2.1 MANUFACTURER

 

��� A.� Provide products manufactured by Fuller O'Brien Paints, headquartered at 395 Oyster Point Boulevard, Suite 350, South San Francisco, CA� 94080.

 

��� B.� Substitutions will not be acceptable.

 

2.2 MATERIALS

 

��� A.� Coatings:� Ready mixed, except for field catalyzed coatings; having good flow and brushing properties and consistent drying or curing behavior, free of sags and streaks.

 

��� B.� Accessory Materials:� Linseed oil, turpentine, paint thinners and other materials recommended by coatings manufacturer as necessary to achieve finishes specified.

 

��� C.� Patching and Surface Preparation:� Latex fillers as recommended by coatings manufacturer.

 

 

PART 3� EXECUTION

 

3.1 EXAMINATION

 

��� A.� Verify that site environmental conditions are appropriate and substrates are in proper condition to receive work of this section.

 

��� B.� Verify that shop applied primers are compatible with specified finish coats.

 

��� C.� Measure moisture content of surfaces using an electronic moisture meter.� Do not begin application of coatings unless moisture content of surfaces is below the following maximum values:

������� 1.� Gypsum wallboard:� 12 percent.

������� 2.� Plaster:� 12 percent.

������� 3.� Masonry surfaces:� 12 percent.

������� 4.� Wood surfaces:� 15 percent.

������� 5.� Vertical concrete surfaces:� 12 percent.

������� 6.� Horizontal concrete surfaces:� 8 percent.

 

3.2 PREPARATION

 

��� A.� Remove or mask electrical plates, hardware, light fixture trim, and similar fittings prior to beginning painting operations.

 

��� B.� Correct defects and clean surfaces affecting work of this section.� Remove existing coatings that are flaking or otherwise in unacceptable condition to receive paint.

 

��� C.� Seal with shellac or other coating acceptable to paint manufacturer any marks or defects that might bleed through paint finishes.

 

��� D.� Remove mildew from impervious surfaces by scrubbing with solution of trisodium phosphate and bleach.� Rinse with clean water and allow substrate to dry.

 

��� E.� Concrete and Masonry Surfaces:� Remove dirt, loose mortar, scale, salts, alkalies, and other detrimental substances.� Remove oils and grease with solution of trisodium phosphate;� rinse well and allow to dry.

 

��� F.� Concrete Floors:� Remove dirt and grease, acid etch, and rinse with clear water.

 

��� G.� Plaster and Drywall:� Fill hairline cracks, small holes, and imperfections with patching compound, then smooth patches to match adjacent surfaces.

 

��� H.� Interior Wood for Opaque Finish:� Remove dirt and foreign matter. Patch knots, pitch pockets, and other surface imperfections with patching compound and seal with sealer recommended by paint manufacturer.

 

��� I.� Interior Wood for Transparent Finish:� Remove dirt and foreign matter. Seal knots and pitch pockets with sealer recommended by stain manufacturer.� Fill nail holes and other surface imperfections with tinted calking compound after sealer has been applied.

 

��� J.� Wood Doors:� Seal top and bottom edges with specified primer.

 

��� K.� Metal Doors:� Seal top and bottom edges with specified primer.

 

��� L.� Galvanized Metal Surfaces:� Remove oils and wash with solvent.

 

��� M.� Aluminum Surfaces:� Remove surface contamination by steam or high pressure water.� Remove oxidation by acid etching and solvent washing.� Apply specified primer as soon as cleaned surfaces are dry.

 

3.3 APPLICATION

 

��� A.� Apply paint products in accordance with manufacturer's printed instructions.� Do not apply coatings to surfaces that are not dry.

 

��� B.� Apply each coat to uniform thickness and finish, with each coat slightly darker than preceding coat.� Allow each coat to dry thoroughly before applying next coat.

 

��� C.� Sand wood and metal surfaces lightly between coats. Vacuum surfaces free of loose particles prior to application of next coat.

 

3.4 CLEANING AND PROTECTION

 

��� A.� Keep project premises free of painting-related debris.� Collect material that may constitute a fire hazard, place in closed metal containers, and remove daily from site.

 

��� B.� Protect work adjacent to painting operations from paint spatters and spills.� Immediately remove paint that falls on finished surfaces not scheduled to receive paint, using materials and techniques that will not damage affected surfaces.

 

3.5 SCHEDULE

Select substrates and finishes required for Project;� delete others.� Note:� XX following product number indicates availability in colors.

��� A.� Concrete, Concrete Block, Plaster, Smooth and Textured Drywall, Unglazed Brick:

������� 1.� Primer:

����������� a.� Plaster:� 1 coat 220-06 Alkyd Wall Primer Sealer.

����������� b.� Concrete Block, Filled:� 1 coat 280-00 Block Filler.

����������� c.� Concrete Block, Unfilled:� 1 coat 220-20 Pro-Tech Wall Primer.

����������� d.� Smooth or Textured Drywall, Concrete, Unglazed Brick:� 1 coat 220-20 Pro-Tech Wall Primer.

������� 2.� Gloss Finish:

����������� a.� Alkyd:

�������������� 1)� 1 coat appropriate wall primer.

�������������� 2)� 1 or 2 coats 612-XX Gloss Enamel.

Select coating above or below for finish.

�������������� 3)� 1 or 2 coats 312-XX VOC Compliant Gloss Enamel.

������� 3.� Semi-Gloss Finish:

����������� a.� Alkyd:

�������������� 1)� 1 coat appropriate wall primer.

�������������� 2)� 1 or 2 coats 206-XX Semi-Gloss Enamel.

Select coating above or below for finish.

�������������� 3)� 1 or 2 coats 297-XX VOC Compliant Semi-Gloss Enamel.

����������� b.� Alkyd Accent Colors:

�������������� 1)� 1 coat appropriate wall primer.

�������������� 2)� 2 coats 619-XX Ultra Color Interior/Exterior Alkyd Semi-Gloss Enamel.

����������� c.� Acrylic Latex:

�������������� 1)� 1 coat appropriate wall primer.

�������������� 2)� 2 coats 214-XX AA 100 percent Acrylic Semi-Gloss.

����������� d.� Acrylic Latex Accent Colors:

�������������� 1)� 1 coat appropriate wall primer.

�������������� 2)� 2 coats 639-XX Ultra Color Interior/Exterior Latex Semi-Gloss.

������� 4.� Gloss Finish:

����������� a.� Acrylic Latex:

�������������� 1)� 1 coat appropriate wall primer.

�������������� 2)� 1 or 2 coats 213-XX 100 percent Acrylic Gloss Enamel.

������� 5.� Eggshell Finish:

����������� a.� Alkyd:

�������������� 1)� 1 coat appropriate wall primer.

�������������� 2)� 1 or 2 coats 208-XX Eggshell Enamel.

����������� b.� Acrylic Latex:

�������������� 1)� 1 coat appropriate wall primer.

�������������� 2)� 1 or 2 coats 212-XX 100 percent Acrylic Eggshell Enamel.

������� 6.� Flat Finish:

����������� a.� Acrylic Latex:

�������������� 1)� 1 coat appropriate wall primer.

�������������� 2)� 1 or 2 coats 202-XX Flat Latex Wall Paint.

����������� b.� Acrylic Latex Accent Colors:

�������������� 1)� 1 coat appropriate wall primer.

�������������� 2)� 2 coats 609-XX Ultra Color Interior/Exterior Latex Flat.

������� 7.� Flat Stipple Finish:

����������� a.� Latex:

�������������� 1)� 1 coat appropriate wall primer.

�������������� 2)� 1 coat 209-00 Flat Latex Satin Stipple.

�������������� 3)� 1 coat 202-XX Flat Latex Wall Paint.

������� 8.� Eggshell Stipple Finish:

����������� a.� Alkyd:

�������������� 1)� 1 coat appropriate wall primer.

�������������� 2)� 1 coat 209-05 Latex Satin Stipple.

�������������� 3)� 1 coat 208-XX Eggshell Enamel.

����������� b.� Acrylic Latex:

�������������� 1)� 1 coat appropriate wall primer.

�������������� 2)� 1 coat 209-05 Latex Satin Stipple.

�������������� 3)� 1 coat 212-XX AA 100 percent Acrylic Eggshell Enamel.

Gloss finishes on smooth surfaces tend to highlight imperfect drywall joints.� Semi-gloss and gloss stipple finishes are recommended for drywall, especially in situations subject to grazing light.

������� 9.� Semi-Gloss Stipple:

����������� a.� Alkyd:

�������������� 1)� 1 coat appropriate wall primer.

�������������� 2)� 1 coat 209-05 Latex Satin Stipple.

�������������� 3)� 1 coat 206-XX Semi-Gloss Enamel.

Select coating above or below for finish.

�������������� 4)� 1 coat 297-XX Low VOC Compliant Semi-Gloss Enamel.

������� 10. Gloss Stipple:

����������� a.� Alkyd:

�������������� 1)� 1 coat appropriate wall primer.

�������������� 2)� 1 coat 209-05 Latex Satin Stipple.

�������������� 3)� 1 coat 612-XX Versaflex Heavy Duty Gloss Enamel.

Select coating above or below for finish.

�������������� 4)� 1 coat 312-XX VOC Compliant Heavy Duty Industrial Gloss Enamel.

 

��� B.� Acoustic Plaster, Acoustic Tile:

������� 1.� Flat Finish:

����������� a.� Latex:

�������������� 1)� 1 or 2 coats 109-20 Ceiling Paint.

����������� b.� Acrylic Latex Accent Colors:

�������������� 1)� 2 coats 609-XX Ultra Color Interior/Exterior Latex Flat.

 

��� C.� Concrete Floors and Decking:

������� 1.� Gloss Finish:

����������� a.� Alkyd:

�������������� 1)� 1 coat 630-XX Porch and Floor Enamel (thinned 10 percent).

�������������� 2)� 2 coats 630-XX Porch and Floor Enamel.

������� 2.� Satin Finish:

����������� a.� Acrylic Latex:

�������������� 1)� 1 coat 631-XX Latex Floor Enamel (thinned 10 percent).

�������������� 2)� 2 coats 631-XX Latex Floor Enamel.

������� 3.� Clear, Water Repellent Finish:

����������� a.� Waterborne:

�������������� 1)� 1 coat 9340 Ful-Seal Regular Water Repellent.

 

��� D.� Woodwork:� Wood Paneling, Wood Trim, Doors, Cabinets:

������� 1.� Stained and Varnished Finish:

����������� a.� Stain:

�������������� 1)� 1 coat 640-XX PenChrome Wood Stain, instead of first coat specified below.

�������������� 2)� Finish as specified below.

������� 2.� Clear Gloss Finish:

����������� a.� Varnish:

�������������� 1)� 1 coat 650-00 PenChrome High Lustre (thinned 10 percent).

�������������� 2)� 1 or 2 coats 650-00 PenChrome High Lustre.

����������� b.� Polyurethane:

Select one of the two following primers.

�������������� 1)� 1 coat 652-00 PenThane Gloss (thinned 10 percent).

�������������� 2)� 1 coat 653-00 VOC Compliant PenThane Gloss.

Select one of the two following finishes.

�������������� 3)� 1 or 2 coats 652-00 PenThane Gloss.

�������������� 4)� 1 or 2 coats 653-00 VOC Compliant PenThane Gloss.

����������� c.� Lacquer:

�������������� 1)� 1� coat S-67 MacLac High Solids Sanding Sealer.

�������������� 2)� 2 coats G-26 MacLac Gloss Lacquer.

������� 3.� Clear Semi-Gloss Finish:

����������� a.� Lacquer:

�������������� 1)� 1� coat S-67 MacLac High Solids Sanding Sealer.

�������������� 2)� 2 coats F-12 MacLac Semi-Gloss Lacquer.

������� 4.� Clear Satin Finish:

����������� a.� Lacquer:

�������������� 1)� 1� coat S-67 MacLac High Solids Sanding Sealer.

�������������� 2)� 2 coats F-16 MacLac Satin Lacquer.

����������� b.� Varnish:

�������������� 1)� 1 coat 650-00 PenChrome High Lustre (thinned 10 percent).

�������������� 2)� 1 or 2 coats 650-01 PenChrome Satin Varnish.

����������� c.� Polyurethane:

Select one of the two following primers.

�������������� 1)� 1 coat 652-00 PenThane Gloss (thinned 10 percent).

��� ����������� 2)� 1 coat 653-00 VOC Compliant PenThane Gloss.

Select one of the two following finishes.

�������������� 3)� 1 or 2 coats 652-01 PenThane Satin.

�������������� 4)� 1 or 2 coats 653-00 VOC Compliant PenThane Satin.

������� 5.� Clear Flat Finish:

����������� a.� Varnish:

�������������� 1)� 1 coat 650-00 PenChrome High Lustre (thinned 10 percent).

�������������� 2)� 1 or 2 coats 650-02 PenChrome Flat.

������� 6.� Opaque Gloss Finish:

����������� a.� Alkyd:

�������������� 1)� 1 coat 220-07 Alkyd Enamel Undercoat.

�������������� 2)� 2 coats 612-XX Versaflex Heavy Duty Gloss Enamel.

Select coating above or below for finish.

�������������� 3)� 2 coats 312-XX VOC Compliant Heavy Duty Industrial Gloss Enamel.

������� 7.� Opaque Semi-Gloss Finish:

����������� a.� Alkyd:

�������������� 1)� 1 coat 220-07 Alkyd Enamel Undercoat.

�������������� 2)� 2 coats 206-XX Semi-Gloss Enamel.

Select coating above or below for finish.

�������������� 3)� 2 coats 297-XX Low VOC Compliant Semi-Gloss Enamel.

����������� b.� Alkyd Accent Colors:

�������������� 1)� 1 coat 220-07 Alkyd Enamel Undercoat.

�������������� 2)� 2 coats 619-XX Ultra Color Interior/Exterior Alkyd Semi-Gloss Enamel.

����������� c.� Acrylic Latex:

�������������� 1)� 1 coat 220-07 Alkyd Enamel Undercoat.

�������������� 2)� 1 or 2 coats 214-XX "AA" 100 percent Acrylic Semi-Gloss Enamel.

����������� d.� Acrylic Latex Accent Colors:

�������������� 1)� 1 coat 220-07 Alkyd Enamel Undercoat.

�������������� 2)� 2 coats 639-XX Ultra Color Interior/Exterior� Latex Semi-Gloss.

������� 8.� Opaque Eggshell Finish:

����������� a.� Alkyd:

�������������� 1)� 1 coat 220-07 Alkyd Enamel Undercoat.

Note:� Finish below may not be available in all areas.

�������������� 2)� 2 coats 208-XX Eggshell Enamel.

����������� b.� Latex:

�������������� 1)� 1 coat 220-07 Alkyd Enamel Undercoat.

�������������� 2)� 2 coats 212-XX "AA" 100 percent Acrylic Latex Eggshell Enamel.

 

��� E.� Wood Floors, Steps, and Porches:

������� 1.� Gloss Finish:

����������� a.� Alkyd:

�������������� 1)� 1 coat 630-XX Porch and Floor Enamel (thinned 10 percent).

�������������� 2)� 2 coats 630-XX Porch and Floor Enamel.

������� 2.� Satin Finish:

����������� a.� Acrylic Latex:

�������������� 1)� 2 coats 631-XX Latex Floor Enamel.

������� 3.� Clear Gloss Finish:

����������� a.� Polyurethane:

Select one of the two following primers.

�������������� 1)� 1 coat 652-00 PenThane Gloss (thinned 10 percent).

�������������� 2)� 1 coat 653-00 VOC Compliant Gloss.

Select one of the two following finishes.

�������������� 3)� 1 or 2 coats 652-00 PenThane Gloss.

�������������� 4)� 1 or 2 coats 653-00 VOC Compliant Gloss.

����������� b.� Phenolic Varnish:

�������������� 1)� 1 coat 650-03 Gym Floor Finish (thinned 10 percent).

�������������� 2)� 1 or 2 coats 650-03 Gym Floor Finish.

 

��� F.� Architectural Metals:

������� 1.� Primer:

����������� a.� Unprimed ferrous metal:

�������������� 1)� 1 coat 621-04 Alkyd Blox-Rust Primer.

����������� b.� Shop primed ferrous metal:

�������������� 1)� Touch up all bare or abraded areas with 621‑04 Alkyd Blox-Rust Primer.

�������������� 2)� 1 coat 621-04 Alkyd Blox-Rust Primer.

����������� c.� Galvanized metal:

�������������� 1)� Clean and acid etch as necessary.

�������������� 2)� 1 coat 621-05 Latex Blox-Rust Primer.

����������� d.� Aluminum:

�������������� 1)� 1 coat 621-05 Latex Blox-Rust Primer.

������� 2.� Gloss Finish:

����������� a.� Alkyd:

�������������� 1)� 1 coat appropriate metal primer.

�������������� 2)� 2 coats 612-XX Versaflex Heavy Duty Gloss Enamel.

Select coating above or below for finish.

�������������� 3)� 2 coats 312-XX VOC Compliant Heavy Duty Industrial Gloss Enamel.

����������� b.� Acrylic Latex:

�������������� 1)� 1 coat appropriate metal primer.

�������������� 2)� 2 coats 213-XX AA 100 percent Acrylic High Gloss Enamel.

������� 3.� Semi-Gloss Finish:

����������� a.� Alkyd:

�������������� 1)� 1 coat appropriate metal primer.

�������������� 2)� 2 coats 206-XX Alkyd Semi-Gloss Enamel.

Select coating above or below for finish.

�������������� 3)� 2 coats 297-XX VOC Compliant Semi-Gloss Enamel.

����������� b.� Alkyd Accent Colors:

�������������� 1)� 1 coat appropriate metal primer.

�������������� 2)� 2 coats 619-XX Ultra Color Interior/Exterior Alkyd Semi-Gloss Enamel.

����������� c.� Acrylic Latex:

�������������� 1)� 1 coat appropriate metal primer.

�������������� 2)� 2 coats 214-XX AA 100 percent Acrylic Semi-Gloss.

������� 4.� Eggshell Finish:

����������� a.� Alkyd:

�������������� 1)� 1 coat appropriate metal primer.

Note:� The following finish may not be available in all areas.

�������������� 2)� 2 coats 208-XX AA Eggshell Enamel.

����������� b.� Latex:

�������������� 1)� 1 coat appropriate metal primer.

�������������� 2)� 1 or 2 coats 212-XX AA 100 percent Acrylic Eggshell Enamel.

������� 5.� Flat Finish:

����������� a.� Acrylic Latex Accent Colors:

�������������� 1)� 1 coat appropriate metal primer.

�������������� 2)� 2 coats 609-XX Ultra Color Interior/Exterior Latex.

 

��� G.� Metal Flooring, Steps, and Catwalks:

������� 1.� Gloss Finish:

����������� a.� Alkyd:

�������������� 1)� 1 coat 621-04 Blox-Rust Alkyd Metal Primer.

�������������� 2)� 2 coats 630-XX Porch and Floor Enamel.

������� 2.� Satin-Flat Finish:

����������� a.� Latex:

�������������� 1)� 1 coat 621-04 Blox-Rust Alkyd Metal Primer.

�������������� 2)� 2 coats 631-XX Latex Floor Enamel.

 

��� H.� Machinery, Equipment, and Fixtures, Shop Primed:

������� 1.� Gloss Finish:

����������� a.� Modified Alkyd:

�������������� 1)� 1 coat 621-04 Blox-Rust Alkyd Metal Primer.

Note:� Finish coating below may not be available in all areas.

�������������� 2)� 1 or 2 coats 313-XX Speedtec Industrial Enamel (Spray Application Only).

 

 

Back to SPECDISK Table of Contents


sorabji.com > foundcrap > found floppies > specdisk